210-065 Real Exam Dumps Questions and answers 61-70

Get Full Version of the Exam
http://www.EnsurePass.com/210-065.html

Question No.61

In this item, you will need to use all information presented to you to successfully answer the question.

image

image

The C-Series endpoint (codec) does not register with the Video Communication Server that is located in a different network. Based on the exhibits, what could be causing the issue?

A.

The subnet mask on the codec is incorrect.

B.

The ip address of the codec is incorrect.

C.

The interface that the codec is in is in the wrong VLAN.

D.

The codec did not receive a DHCP address from the DHCP server.

Correct Answer: A

Explanation:

The subnet mask configured on the codec is 255.255.255.128, when it should be 255.255.255.0.

Question No.62

A video engineer needs to locate the running version of the Cisco VCS. Under which tab in the Cisco VCS web interface is this information contained?

A.

Applications

B.

Status

C.

System

D.

Configuration

Correct Answer: B

Question No.63

Refer to the exhibit. Which option performs a factory reset of a Cisco TelePresence System endpoint?

image

A.

Configuration gt; System Settings

B.

Configuration gt; Security Settings

C.

Troubleshooting gt; Hardware setup

D.

Monitoring

E.

Troubleshooting gt; Configuration Issues

F.

Troubleshooting gt; System Restart

G.

A Cisco TelePresence System endpoint can be reset only via CLI.

Correct Answer: E

Question No.64

What is the importance of defining option 150 in the DHCP server for Cisco TelePresence endpoints?

A.

Option 150 is not important.

B.

It is the TFTP server IPv4 address where the video endpoint retrieves its configuration file while booting.

C.

It is the IPv4 address of the default gateway for the subnet that the video endpoint is connected to.

D.

It is the configured SIP registrar and proxy server.

E.

It is the unique NTP server IPv4 address.

image

Correct Answer: B

Question No.65

Which two methods can be used to set the default call protocol of a Cisco TelePresence endpoint running TelePresence codec firmware? (Choose two.)

A.

Use the GUI and set System gt; H.323 gt; Settings gt; Default Call Protocol gt; H.323.

B.

Use the CLI command xConfiguration Conference 1 DefaultCall Protocol: H323.

C.

Use the CLI command Conference Default Protocol: H323.

D.

Use the CLI command Default Protocol: H323.

E.

Use the GUI and set Configuration gt; System Configuration gt; Conference gt; DefaultCall gt; H.323.

Correct Answer: BE

Question No.66

A customer requests a configuration that enables users to easily add a third party to an existing call. The environment contains only three Cisco TelePresence C40 codecs and one Cisco VCS. To achieve the customer#39;s requirements, which feature should be added?

A.

Cisco MultiWay

B.

Cisco TelePresence Conductor

C.

Cisco TMS

D.

Cisco Multisite

E.

Cisco VCS Expressway

Correct Answer: D

Question No.67

A technician enters the diag system normal command for a Cisco TelePresence System endpoint. Which action must be done in the CLI before entering this command?

A.

Logging must be enabled.

B.

Calling services must be stopped.

C.

All forced upgrades must be cleared.

D.

The Telephone_Srvr service must be restarted.

Correct Answer: B

Question No.68

Which all-in-one dual-screen solution can be used for an average meeting room without the need for external monitors?

A.

MX700

B.

MX300G2

C.

EX90

D.

SX80

E.

TX9000

F.

MX200G2

image

Correct Answer: A

Question No.69

Refer to the exhibit. Which system tab can be used to add video infrastructure devices and endpoints?

image

A.

Navigator

B.

System Overview

C.

Configuration Templates

D.

Provisioning

E.

Administrative Tools

Correct Answer: A

Question No.70

An engineer wants to know if there is a way to determine the optical zoom of a Cisco TelePresence SX20 remotely. Which two methods will retrieve this information? (Choose two.)

A.

From the CLI, run xstatus.

B.

From the CLI, run xconfig.

C.

From the web GUI, choose Configuration gt; System Status gt; Camera.

D.

From the web GUI, choose Configurationgt; Camera gt; Status.

E.

From CLI, run xcommand camera.

Correct Answer: AC

image

Get Full Version of 210-065 Dumps

Tagged

Leave a Reply

Your email address will not be published. Required fields are marked *